ZYNQ程序固化问题

cmd /C program_flash -f C:\Users\ZYZD\project_2\project_2.sdk\fsbl\bootimage\BOOT.bin \
-offset 0 -flash_type qspi-x4-single -fsbl \
C:\Users\ZYZD\project_2\project_2.sdk\fsbl\Debug\fsbl.elf -cable type xilinx_tcf url \
TCP:127.0.0.1:3121

****** Xilinx Program Flash
****** Program Flash v2018.3 (64-bit)
  **** SW Build 2405991 on Thu Dec  6 23:38:27 MST 2018
    ** Copyright 1986-2018 Xilinx, Inc. All Rights Reserved.


Connected to hw_server @ TCP:127.0.0.1:3121
Available targets and devices:
Target 0 : jsn-JTAG-SMT2-C3064A97ABCD
        Device 0: jsn-JTAG-SMT2-C3064A97ABCD-4ba00477-0

Retrieving Flash info...

Initialization done, programming the memory
===== mrd->addr=0xF800025C, data=0x00000001 =====
BOOT_MODE REG = 0x00000001
WARNING: [Xicom 50-100] The current boot mode is QSPI.
If flash programming fails, configure device for JTAG boot mode and try again.
===== mrd->addr=0xF8007080, data=0x30800100 =====
===== mrd->addr=0xF8000B18, data=0x80000000 =====
Downloading FSBL...
Running FSBL...
Finished running FSBL.
===== mrd->addr=0xF8000110, data=0x00177EA0 =====
READ: ARM_PLL_CFG (0xF8000110) = 0x00177EA0
===== mrd->addr=0xF8000100, data=0x0001A008 =====
READ: ARM_PLL_CTRL (0xF8000100) = 0x0001A008
===== mrd->addr=0xF8000120, data=0x1F000400 =====
READ: ARM_CLK_CTRL (0xF8000120) = 0x1F000400
===== mrd->addr=0xF8000118, data=0x00177EA0 =====
READ: IO_PLL_CFG (0xF8000118) = 0x00177EA0
===== mrd->addr=0xF8000108, data=0x0001A008 =====
READ: IO_PLL_CTRL (0xF8000108) = 0x0001A008
Info:  Remapping 256KB of on-chip-memory RAM memory to 0xFFFC0000.
===== mrd->addr=0xF8000008, data=0x00000000 =====
===== mwr->addr=0xF8000008, data=0x0000DF0D =====
MASKWRITE: addr=0xF8000008, mask=0x0000FFFF, newData=0x0000DF0D
===== mwr->addr=0xF8000910, data=0x000001FF =====
===== mrd->addr=0xF8000004, data=0x00000000 =====
===== mwr->addr=0xF8000004, data=0x0000767B =====
MASKWRITE: addr=0xF8000004, mask=0x0000FFFF, newData=0x0000767B




U-Boot 2018.01-00073-g63efa8c-dirty (Oct 04 2018 - 08:22:22 -0600)



Model: Zynq CSE QSPI Board

Board: Xilinx Zynq

Silicon: v3.1

DRAM:  256 KiB

WARNING: Caches not enabled

Using default environment



In:    dcc

Out:   dcc

Err:   dcc

Zynq> sf probe 0 0 0


SF: unrecognized JEDEC id bytes: 00, 00, 00

Failed to initialize SPI flash at 0:0 (error -2)

Zynq> ERROR: [Xicom 50-186] Error while detecting SPI flash device - unrecognized JEDEC id bytes: 00, 00, 00

Problem in running uboot
Flash programming initialization failed.

ERROR: Flash Operation Failed

不知道是什么原因造成的呢？